RoboK SiteLens® – AI Safety Monitoring on Your Existing CCTV

RoboK SiteLens is AI safety monitoring for the CCTV you already have. It uses computer vision to turn a site’s existing camera feeds into a record of near misses, people in vehicle routes and other safety events: the time, the place and the clip, on every shift. It reports what it records by zone and shift, usually without new cameras.

RoboK SiteLens at a glance

What it is
AI safety monitoring software. It uses computer vision on the CCTV a site already has.
What it records
Near misses between people and vehicles, people in vehicle routes and outside marked walkways, entries to restricted zones, PPE, working at height on vehicles, trailers and loads, smoking in areas the site marks as no-smoking, and vehicles over a set speed limit. Each event comes with the time, the zone and the clip.
Where it is used
Ports and terminals, shipyards, logistics and warehousing, and manufacturing sites. Available in the UK, Europe and the US.
Setup and support
Set up remotely or on site, on your existing cameras or our 4G camera. Support covers US hours, and new detections can be added on request.
Cameras
Usually your existing CCTV. We assess each camera first, and can supply one where a zone has no usable camera.
Data
Processed and stored securely; where it is held is set out in your contract. RoboK is Cyber Essentials certified and a University of Cambridge spinout, founded in 2017.
How to start
Safety Mapping: a free two-week trial on one camera position. Use ours, on its own 4G with no access to your network, or one of your own cameras, typically one to two weeks from camera access to the first events.

See all features: what it detects and what you get

How It Works

RoboK SiteLens® connects to your site’s CCTV and watches the feeds continuously, across every shift. It records safety events including people close to moving vehicles, people outside marked walkways, entries to restricted zones, PPE and working at height. Each event is logged with the time, the place and the clip. Spill detection is also available for manufacturing sites.

Your risk assessment sets the controls. The cameras check them.

  1. Your risk assessment: Pick the assessments that matter most, starting with any revised recently.
  2. Cameras check the controls: Walkways, exclusion zones, PPE: is each control effective on the ground?
  3. Clips show what needs to change: Each event arrives as a short clip with its time and place. Trends show where a control is not effective.
  4. Your team makes the change: A barrier, a rule, a new route, a briefing.
  5. Trends show whether it worked: The same cameras keep checking, so you see the before and after.

Runs on the cameras you already have, with a RoboK 4G camera where there is no view. Need a starting point? See our worked transport risk assessment.

Safety Reporting

Track hazard counts by category and how they change over time, on the areas you choose to cover. Alongside incident figures, you get a measure of what happens before an incident: the near misses and unsafe moments that usually go unreported.

Results

The thinking behind RoboK SiteLens®

Why it is built this way: Plan, Do, Check, Act: The Check Is the Hard Part, Active and Reactive Monitoring: What HSG65 Actually Asks For, Hierarchy of Controls: The Five Levels, Most to Least Effective, and How We Think About Safety. Tools: Is it RIDDOR reportable? and the near-miss log template.

RoboK SiteLens® FAQs

What is RoboK SiteLens? RoboK SiteLens is workplace safety monitoring software. It connects to the CCTV a site already has and uses computer vision to record near misses, pedestrian–vehicle interactions, entries to restricted zones and PPE, and reports them by zone and shift.

Do we need new cameras to use RoboK SiteLens? Usually not. RoboK SiteLens runs on the CCTV a site already has, where camera position and image quality are good enough; we assess each camera before relying on it. Where a zone has no usable camera, we can supply one. Sites can also start with Safety Mapping: a free two-week trial on one camera, either ours on its own 4G connection with no access to your network, or one of the site's own. We check the camera's view first (a still image is enough). If it doesn't show the area clearly, we start on our camera instead.

What happens during the free two-week Safety Mapping trial, and after it? One camera watches the area you worry about most for two weeks, either ours on its own 4G or one of yours, and records what happens there on every shift. At the end you get a written report and a review call. If you carry on, it continues as an annual subscription on the same camera position; if not, you keep the report and there is nothing to pay.

What can RoboK SiteLens detect? People close to moving vehicles, including forklift and pedestrian near misses; people walking outside marked walkways; entries to restricted zones you define; PPE (high-visibility clothing, hard hats and protective clothing where required); people working at height on vehicles, trailers and loads; vehicles over a set speed limit; and smoking in areas the site marks as no-smoking. Spill detection (liquid on the floor, flagged as a slip risk) is also available. Each event is recorded with the time, the zone and the clip, and new detections can be added on request.

How can we capture near misses that are never reported? RoboK SiteLens records near misses between vehicles and people from the camera feeds, so they are captured without depending on someone noticing and reporting them. Over weeks, that shows where and when they happen, alongside your incident figures.

What can we put in place after a workplace safety incident to prevent recurrence? Monitoring of the area or behaviour involved, so unsafe interactions and near misses are recorded rather than depending on someone observing and reporting them. Every event is timestamped and categorised, which gives an evidence trail for the investigation and a way to see whether the control you put in place is effective.

How quickly can we get started, and when will we see the first events? On our camera, Safety Mapping needs only mains power: it runs on its own 4G, with no IT involvement. On a site's own cameras, RoboK SiteLens typically takes one to two weeks from camera access to the first events, including assessment, configuration and training.

Where do you work, and how is it set up? RoboK SiteLens is available in the UK, Europe and the US. Setup is remote or on site, and support covers US hours.

How is RoboK SiteLens data handled? All data is processed and stored securely; where it is held is set out in your contract. Footage is kept for 30 days as standard and clips flagged as hazards for the length of your subscription; both can be changed in your contract. Faces can be blurred on request, access is limited to named user accounts, and RoboK is Cyber Essentials certified. Our data-handling documents and DPA are available on request.

How are people's faces handled? Faces can be blurred on request, and areas you don't need to monitor can be masked. Access to footage is limited to named user accounts.

Which industries use RoboK SiteLens? Ports and terminals, logistics and warehousing, and manufacturing. We have also worked on roadworks and at a railway level crossing.